In the central position, the equalizer is off flat. The circuitry of the British EQs is based on the technology used in the best-known top-of-the-line consoles and providing a warm sound without any unwanted side effects.
The upper HIGH and the lower LOW bands are shelving filters that increase or decrease all frequencies above or below their cut-off frequency.
The cut-off frequencies. For the mid range, the console features a semi-parametric equalizer with a filter quality Q of 1 octave, tunable from Hz to 8 kHz. When the PRE switch is pressed down, the associated aux send is taken pre-fader. The aux send marked FX offers a direct route to the built-in effects processor and is therefore post-fader and post-mute.
Monitor and effects busses AUX sends source their signals via a control from one or more channels and sum these signals to a so-called bus. In the latter case, the effects return can then be brought back into the console via the aux return connectors.
When using effects on a channel signal, it is usual to have the aux send post fader so that the balance between effect and dry signal stays constant even when the channel fader is altered. If this were not the case, the effects signal of the channel would remain audible even when the channel fader is turned all the way down.
For monitoring, the aux sends are. The PAN control determines the position of the channel signal within the stereo image. When working with subgroups, you can use the PAN control to assign the signal to just one output, which gives you additional flexibility.
For example, when routing to subgroups 3 and 4, panning hard left will route the signal to group output 3 only, and panning hard right will route to group output 4 only.
The MUTE switch breaks the signal path pre-channel fader, hence muting that channel in the main mix. The aux sends which are set to post-fader are likewise muted for that channel, while the pre-fader monitor paths remain active irrespective of whether the channel is muted or not. This enables you to listen to a channel signal without affecting the main output signal. The signal you hear is taken either before the pan control PFL, mono or after the pan and channel fader Solo, stereo cf.
The SUB switch routes the signal to the corresponding subgroups. The FX has 4 subgroups and The MAIN switch routes the signal to the main mix bus. Each stereo channel has two balanced line level inputs on jacks for left and right channels. Both jack inputs will also accept unbalanced connectors. Use this control to adjust the line signal levels on channels FX only. The stereo channels contain a stereo EQ section. The cut-off frequencies of the high and low bands are 12 kHz and 80 Hz respectively, while the center frequencies of the high-mid and low-mid bands are 3 kHz and Hz respectively.
Both mid range bands are of the peak filter type. A stereo EQ is superior to two mono EQs on a stereo signal as two separate EQs will usually result in a discrepancy between left and right channels. In principle, the aux sends of the stereo channels function the same way as those of the mono channels.
As the aux sends are mono, the send from a stereo channel is first summed to mono before it reaches the aux bus. Welcome to ManualMachine. We have sent a verification link to to complete your registration.
Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions.
Enter a new password. Thank you Congratulations! With the addition of the latest digital technology these best-in-class consoles combine the advantages of both analog and digital technology.
Table of Contents Thank you Download them by going to the appropriate product page at: www. Caution To reduce the risk of electric shock, do not remove the top cover or the rear section. Caution To reduce the risk of fire or electric shock, do not expose this appliance to rain and moisture.
Caution These service instructions are for use by qualified service personnel only. Unlike conventional circuitry an SMPS provides an optimum supply current regardless of the input voltage. Frequency response correction Using the equalizers found in each channel strip, you can simply, quickly and effectively adjust the way a signal sounds.
Effects mixing In addition to the effects processor contained in your mixer, using the insert connectors on the mono channels and both aux busses lets you insert additional signal processors into your signal path. To arrange for warranty service, please contact the retailer from whom the equipment was purchased.
Thank you for your cooperation! Get fast, free shipping with Amazon Prime. Amazon Music Stream millions of songs. Learn More Shipping Advisory This item must be shipped separately from other items in your order. Out of all of the Behringer models that I have used in this price range, this is the best built on by far. There are 2 subgroups with separate outputs for added routing flexibility and 2 multi-functional stereo aux returns with flexible routing.
Top Reviews Most recent Top Reviews. Did you find this review helpful? Each one of those stereo channels has a 4 band parametric EQ. It is not made anymore jbfx-pro may be hard to find one still in good shape. For warranty information about this product, please click here. Share your thoughts with other customers.
Showing of 9 reviews. See offer for details. Je would do as always with the same choice without problem. Page 1 of 1 Ubx-pro over Page 1 of 1. Especially for the Behringer! Customers who viewed this item also viewed. Amazon Second Chance Pass it on, trade it in, give it a second life. The precision and quality of sound is average maybe a 5 out of Write a user review. This website uses cookies to improve your experience while you navigate through the website.
Provide a clear and comprehensive description of the issue and your question. The more detail you provide for your issue and question, the easier it will be for other Behringer Xenyx FX owners to properly answer your question. Does the unit effects go to the head phones?
If so, how? I followed the manual and can't get the effects. I have not added any power to the mixer yet therefore no speakers, only head phones. Will the effects come out through the speakers if not going to the head phones? View the manual for the Behringer Xenyx FX here, for free.
0コメント